Steel grade P-110, in fact, has the largest window of applicability compared to steel grades Q-125, 140 and 150. Fit for purpose tests performed on steel grade Q-125, with 1 bar of ppH2S and NACE solution A, using NACE TM0177 Method A, at test temperature of 80°C p roduced no SSC failure.
API 5CT K55 Casing Canada Steel and Casing Importsc. Martensitic chromium steel (L80 9Cr and 13Cr) differs from carbon steel in density. The shown weight of martensitic chromium steel is not an exact value. The mass correction factor 0.989 can be used. d. C90, T95 and Q125 steel grade casing should be supplied according to specification, weight and wall thickness listed in the above table or
Dec 03, 2012 · Looks like the API standard is 5AQ. The Q125 is probably something listed in the spec. But 5AQ is no longer being used. IHS states:SPECIFICATION FOR Q125 CASING (COMBINED WITH SPEC 5A, 5AC, AND 5AX INTO SPEC 5CT-88) Note that the -88 on API 5CT-88 is just the year of publication so look for API 5CT instead. API 5CT comes up as active.
API Steel Grade K55, N80, L80, C90, T95, P110, Q125It can be divided into nine categories of steel grade:H-40, J-55, K-55, N-80, L-80, C-90, T-95, P-110, Q-125. In it, the letters are stand for the steel grade, which has no relation with the properties and the number refers to the minimum yield strength. The bigger the number is, the higher yield strength will be.
Alloy Steel Material Grades Alloy Steel Property Data SheetAlloy Steel Q125 API grade for deep well service, not generally for use in sour condensate wells. Quadrant hardness testing is required without any specified limits other than the variation between readings. Impact testing is required for each head and/or lot.
Seamless steel Pipe Piles UBC (ASTM) Welded and Seamless Steel Pipe Piles Min. Yield 36 Min. Tensile Material A36 A252 A-53 J-55 K-55 N-80 L-3C -110 58 48 95 100 95 125 These Steel pipe, black and hot dipped 25 Zinc coated; welded and seamless Steel pipe, black and hot dipped Zinc coated; welded and seamless Steel pipe, black and hot dipped 35
Deep Well Steel Grades:for Deep Drilling EnvironmentsU. S. Steel Tubular Products API steel grades for deep drilling:API P110 is an API grade for general use in deep wells. This grade is not generally considered suitable for sour condensate wells. API Q125 is an API grade for deep well service, not generally for use in sour condensate wells. Quadrant hardness testing is required without any
Grades of octg products and steel grade color codesThe yield strength of J55 and K55 is the same level, the difference of them is that the tensile strength of K55 is higher than that of J55. N80, L80, C90 is same with tubing steel grade. Q125 is divided into Q125-1, Q125-2, Q125-3 and Q125-4. V150 does not conform to API high strength steel grade and it mainly used in deep well or ultra deep well.
API grade for general use in deep wells. This grade is not generally considered suitable for sour condensate wells. Available in casing dimensions of 114.3 mm (4.5") to 406.4 mm (16") Available in tubing dimensions of 26.7 mm (1.05") to 114.3 mm (4.5")
Pan Meridian Tubular - Pan Meridian TubularPan Meridian Tubular is a reliable distributor of high-quality oilfield casing and tubing. We carry a large inventory of casing and tubing, ranging in sizes from 1¼ macaroni to 20 casing. We are accustomed to the time-sensitive nature of the oilfield and can handle your tubular requirements twenty-four hours a day, seven days a week. Pan Meridian Tubular Read More »
Q125Type1 / Q125 Type 1 - steel-gradesStainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. Q125 Type 1 can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc.
Schluter ®-QUADEC is a finishing and edge protection profile for tiled edges and outside corners of tiled surfaces, and is distinguished by its squared reveal surface.. New! Now available in 10 (3.05 m) lengths; Prevents tile edges from chipping; Can be incorporated as an accent within tile fields on floors and wallsQ125 - Energy Alloys, LLCQ125:API 5CT GENERAL SCOPE:API 5CT grades are commonly used in casing, production tubing, coupling stock, pup joints, and various down hole accessories. Energy Alloys stocks a variety of sizes in tubular form for this grade category. Chemical Composition:C Mn