ASTM A572 Gr.50 plate has a higher yield and tensile strength than A36 plate, combined with a lower weight. ASTM A572 Gr.50 steel is intended for welded structures primarily in applications where extra strength or reduced end product weight is desired without foregoing strength. ASTM A572 Gr.50 plate is used in a variety of structural applications, including bridges, buildings, construction
ASTM A572 Grade 50, 55, 60, 65 Steel Plates Specification A:Specimen shall comply with Specification of A6/A6M. B:Elongation not required to be determi ed for floor plate. C:For wide flange shapesover 426 lb/ft [634 kg/m], elongation in 2 in. [50 mm] of 19% minimum applies. D:For plates wider than 24 in. [600 mm], the elongation requirement is reduced two percedntage points for Grade 42, 50, and 55 [290,345,and 380], and three percentage points
Corporate Headquarters 33900 Doreka Drive Fraser, MI 48026. Laser & Fabrication Operations 25770 Groesbeck Hwy Warren, MI 48089
ASTM SPECIFICATION CONVERSION WITH TYPICAL Grade 50 (Class 1) Grade 50 (Class 2) Structural Quality (SQ) ASTM 446 Grade A Grade B Grade C Grade D (Class 1) * * * NOTE:THE ROCKWELL RANGES AND MECHANICAL PROPERTIES ARE TYPICAL TO EACH QUALITY OF STEEL AND MAY VARY TO SOME DEGREE The Forming Steel (FS) designation will encompass the properties of the previous Drawing Quality (DQ) grade in
Asme SA516 Grade 70|SA516 Grade 60 Steel Plate SpecificationASME SA516 grade introduction:SA516 grade 55, SA516 grade 60, SA516 grade 65, SA516 grade 70. These 4 grades are mainly defined by their different tensile and yield strength range, which is influenced by content of Carbon. For example sa 516 grade 70 has the highest tensile and yield strength range due to the highest Carbon content(up to0.28%).
Type 7, 3/16 to 2 in. thick, steel plate, A high strength, low alloy steel grade with excellent mechanical and fabricating properties. A656 is produced as a killed steel with fine grain practice, it is available in four strength levels. Normal uses
CTS TubesASTM A192 / ASME SA192 Tubes mechanical property requirements do not apply to tubing smaller than 18 in. [3.2 mm] inside diameter or 0.015 in. [0.4 mm] thickness. [50.8 to 76.2], excl 2500  ASTM A192 / ASME SA192 Flattening Test ASTM A210 / ASME SA210 GRADE C Seamless tubes
Carbon and low alloy steel plate - BBN SteelCarbon and low alloy steel also known as Mild steel. steels with a low carbon content and without alloy are softer and more easily formed, it is a low-cost material that is easy to shape. While not as hard as higher-carbon steels, carburizing can increase its surface hardness. carbon structural steel has the proper tensile strength, good toughness, plasticity, processing property.
Grade U.S. [SI] ksi [MPa] 55  55 75 [380 515] 60  60 80 [415 550] 65  65 85 [450 585] 70  70 90 [485 620] 1.3 The maximum thickness of plates is limited only by the capacity of the composition to meet the speci ed mechanical property requirements; however, current prac-tice normally limits the maximum thickness of plates fur-ASTM A656 Steel PlateGrade 50, 60, 70, 80 A656 Stockists of High Tensile plates, Stockist and suppliers of High performance steel plates, stockist & suppliers of ASTM ASTM A656 Gr.- Grade 50, 60, 70, 80 Grade 65 Steel Plate - ASTM A656 Gr.- Grade 50, 60, 70, 80 Grade 65Plate in europe, stockist & suppliers of Astm ASTM A656 Gr.- Grade 50, 60, 70, 80 Grade 65 Plates, Metal & Metal Made Products, stockist & exporters of of ASTM ASTM A656 Gr